I have neither of these. A proper soft water system not only has a loop, but all the outside faucets are connected to the raw water so that the yard does not get watered with soft water. In every installation, you have to plan ahead. In many communities hard water is a fact of life--mineral build-up is just something that happens. Do not install your softener downstream from your water heater, as the high temperatures could damage the unit. Some water supply lines enter the home on the garage side and some the non garage side of the home. Photobucket A water softener is usually installed near the water heater.
If I did that, getting power and a drain line to the softener would still be a concern. Drain A water softener should also be near a drain. Lots of factors affect the installation of any particular water softener. Some smaller units may be installed beneath specific fixtures commonly kitchen sinks , but only soften the water for that fixture, not the entire home. Also, you will need to have a location for the drain.
This should be done as regular maintenance once per year. As common as this can be, long-term build-up creates plumbing nightmares that dramatically affect even the simplest home maintenance tasks. Hello, I am moving from a house with a Softener to one without. It saves you from additional plumbing which means you can install the water softener yourself. Water connected at the primary water inlet helps distribute soft water to the whole house.
So, if you are unsure about this part of the job then I would suggest hiring a professional instead rather than trying to accomplish the task on your own. I would like to put in a water softener but I'm uncertain that I should re-plumb my water into the garage and back to the east wall into the house. As you might expect, the harder your water, the higher your water softening cost will be. Don founded HomeTips in 1996. I went through this about five years ago. Types of Water Softeners There are four different types of water softeners: ion-exchangers, salt-free, dual tank and magnetic.
Lower-end models are significantly more affordable. The injectors may also become clogged, which will require a special cleaning. I looked at your pictures and it is almost identical to my setup in my garage. Many units will also come with a bypass valve already installed; refer to your manual in this case. Why Add A Water Softener? Skills necessary: cutting and joining copper or steel pipe.
In many cases, the company you purchase the unit from will be able to assist with installation, preferring to give you a package deal on purchase and install. Installing a Water Loop Installing a water loop can be an easy task, but gets difficult in larger homes. These are generally known as conventional water softeners. Options include a floor drain, utility sink, or sump pump. A free water test of well water is probably more expensive than one that you pay for, because it will be provided by a salesman who will be looking to sell you an expensive system. Home Maintenance Hard water build-up is similar to cholesterol in the way it collects in pipes and faucets--causing severe blockage overtime. If you do I would box it and put heat trace on the softener and lines.
Step by Step Guide to Installing a Water Softener Yourself It takes 1-4 hours to install a water softener in a pre-plumbed house. Installing a water softening system is a great way to help solve these problems, giving you fresh clear water any time you want it. Make sure that the drain pipe is 2 inches and above from the drain hole. Tell us in the comments section below. I want to soften the whole house except for cold water in kitchen as I think is the norm - sodium drinking water and all that bs, not that I care but future owners might. These beads carry a negative charge and attract the unwanted minerals, which carry a positive charge. If none are found, open the valves all the way to start the system.
This will allow you to install the elbow fittings which enables you to run two lines to the inlet and outlet ports of the bypass valve. Tighten the pipe cutter onto the pipe and rotate it around the pipe to make the cut. You only need to run one pipe from the water meter to the softener. Test the hardness of the water before installing a water softener. I'm thinking of installing a softener myself, but will rethink it if a loop needs to go in. I understand that any line on a relief valve is supposed to be straight and as short as possible - to deliver the relieved hot water straight out without the possibility of back pressure or failure.
If your softener is under five years old, repairing it will be a better option than replacing it--it may still be under warranty. The salt helps remove the hardness from the water. If you do require salt-free drinking water, potassium is recommended. Where to connect to pipes. If you have pipes of different sizes, you may want to use a small-size fitting to get the right size that will go with the plastic valves. The brine material needs to be replaced periodically. A water loop will appear as an extra copper pipe located on the wall nearby your water heater.
The loops often come out of the pipes in the wall or come up from the pipes under the floor. Would you like to answer one of these instead? Furthermore, many people who have made the switch from hard to soft water will agree that soft water leaves the skin feeling smoother and healthier. If there is no loop, and the water service line plumbing is exposed, you install a softener the same way as with a loop and run the drain line to a drain line, sump pump or floor drain etc. Do not put the softener in an area where freezing might occur; this can cause permanent damage and void your warranty. Whole house systems, for example, need to be installed as close to the place where the water enters your house as possible. It all depends on the location site, the state of plumbing in your house, and the type of water softener you want to install.